Products

  • Power Supply for Broadband Noise Source

    0 out of 5
    • Power Supply for Broadband Noise Source.
    • 12V 1A output
    • 5.5mm/2.1mm coaxial connector.
    $8.95
  • Raspberry Pi GPS/RTC Expansion Board

    0 out of 5

    NEW FOR 2020 Now with RAW Output & Hardware RTC

     

    The Uputronics Raspberry Pi GPS/RTC Expansion Board provides a modern multi GNSS GPS receiver and hardware RTC with quick no soldering required connection to all Raspberry Pi boards with the 2×20 header (the original Pi Model A/B are not supported). Featuring PPS (Pulse per second) output to permit the use of the board for PPS disciplined NTP servers, RAW output available from the UBlox™ GPS module and twin super caps for GPS hot start/setting retention & maintaining RTC.

     

    This board retains backwards compatibility with previous generation Uputronics Pi GPS boards. With its features and ease of installation we believe this is the ultimate GPS /  RTC HAT for the Raspberry Pi.

     

    GPS Specifications:

    • 72-channel u-blox™ M8 engine
    • Up to 3 concurrent GNSS (BeiDou,Galileo,GLONASS,GPS/QZSS)
    • Default GNSS: GPS/GLONASS.
    • -167dBm Navigation Sensitivity
    • 10Hz navigation rate in multiGNSS mode, 18Hz in GPS only
    • RAW Output available via UBX-RXM-RAWX Message
    • 3V supplied to antenna port to power active antenna
    • Antenna requirements: Active 3V Ceramic Patch
    • No EEPROM settings must be sent at power up or saved to battery backed RAM.
    • Default baud rate: 9600bps
    • I2C Bus (Address 0x42)
    • Robust SMA antenna connection.

     

    For full documentation please consult the u-blox 8/u-blox M8 receiver description including protocol specification document (UBX-13003221) linked here: https://store.uputronics.com/files/UBX-13003221.pdf

     

    RTC Specifications:

    • Micro Crystal RV-3028-C7 Real Time Clock Module
    • Factory calibrated ±1 ppm @ 25°C
    • I2C Bus (Address 0x52)
    • Built in kernel compatibility
    • Provides year, month, date, weekday, hours, minutes and seconds

     

    In The Box

    1 x Raspberry Pi GPS/RTC Expansion Board
    4 x 11mm standoffs w/8 M2.5 Screws
    1 x Header with 4.93mm tails

     
    Full Data Sheet Here : https://store.uputronics.com/files/Uputronics%20Raspberry%20Pi%20GPS%20RTC%20Board%20Datasheet.pdf

    $44.95
  • Raspberry Pi+ GPS Expansion Board

    0 out of 5

    This is an GPS expansion board designed specifically for the both the version 1,2 and 3 Raspberry Pi+ Models.

    This board is designed for applications that use a GPS connected via the serial ports to the Raspberry Pi such as timing applications or general applications that require GPS information. To facilitate PPS the time pulse output is connected to a GPIO so you can utilize this board to give NTP PPS discipline. PPS does not work without an antenna.

    This board is equipped with the latest Ublox MAX-M8Q positioning module and high quality filtering capacitors and inductors throughout. The MAX-M8Q features a RTC Crystal, very low power usage and high performance. Although not a true timing module it is more than adequate for a Pi based NTP Server. Its worth noting the module can, with a serial command, be placed in “Stationary” dynamic mode which is the default mode for the much more expensive timing modules.

    The board features an SMA connector for an active patch antenna (see related products) power and PPS LED's. On the top is a super capacitor which can be used to retain any custom settings in the event of power loss (If the module is commanded to do so ). The MAX-M8Q is connected via serial to the Pi and the PPS is connected to GPIO18 (pin 12).

    A 2×20 way header is supplied and 2 suitable standoffs providing a very robust solution. The board follows Raspberry Pi's HAT physical layout with camera and display port notches. It is possible to stack additional HAT's on top of this board with the stacking header.

    To use this board to make a Stratum 1 NTP Server please follow these instructions here : http://ava.upuaut.net/?p=726

    Datasheet available here

    For the communication protocol see the u-blox 8 / u-blox M8Receiver DescriptionIncluding Protocol Specification.

    (The command to save settings is CFG-CFG)

    $39.95
  • 20 %

    Remtronix 800 MHz Antenna (BNC)

    0 out of 5
    • The famous 800 MHz antenna
    • Minimum +6dB Gain over standard antenna
    • Engineered and “Made In Japan”
    • Over 20,000 sold through OEM brands
    • Covers 700-900 MHz (works pretty well on 450, too)
    • BNC connector for general use
    • Length: 7″
    $24.95 $19.95
  • 12 %

    Remtronix 800 MHz Antenna (Skinny SMA for SDS100 scanner)

    0 out of 5
    • The famous 800 MHz antenna
    • Minimum +6dB Gain over standard antenna
    • Engineered and “Made In Japan”
    • Over 20,000 sold through OEM brands
    • Covers 700-900 MHz (works pretty well on 450, too)
    • SKINNY SMA connector for use with the Airspy or Uniden SDS100 scanner.
    • Length: 7″
    $24.95 $21.95
  • 12 %

    Remtronix 800 MHz Antenna (Skinny SMA for SDS100 scanner) – Water Resistant

    0 out of 5
    • The famous 800 MHz antenna
    • Minimum +6dB Gain over standard antenna
    • Engineered and “Made In Japan”
    • Over 20,000 sold through OEM brands
    • Covers 700-900 MHz (works pretty well on 450, too)
    • SKINNY SMA connector for use with the Airspy or Uniden SDS100 scanner.
    • Length: 7″
    • o-ring to resist water penetration
    $24.95 $21.95
  • 20 %

    Remtronix 800 MHz Antenna (SMA)

    0 out of 5
    • The famous 800 MHz antenna
    • Minimum +6dB Gain over standard antenna
    • Engineered and “Made In Japan”
    • Over 20,000 sold through OEM brands
    • Covers 700-900 MHz (works pretty well on 450, too)
    • SMA connector for use with the Airspy.
    • Length: 7″
    $24.95 $19.95
  • 7 %

    Remtronix REM-830 800 MHz ANGLE Antenna (BNC)

    0 out of 5
    • The famous 800 MHz antenna
    • Minimum +6dB Gain over standard antenna
    • Engineered and “Made In Japan”
    • Over 20,000 sold through OEM brands
    • Covers 700-900 MHz (works pretty well on 450, too)
    • BNC connector for general use
    • Length: 7″
    • ANGLE connector – perfect for base scanners
    $29.95 $27.95
  • RG6 feedline (Black) with F connectors

    0 out of 5
    • RG6 Quad Shield Cable – Black Jacket
    • F connectors on each end
    • Factory spec coverage to 3 GHz.
    • UL approved
    • Note: 75 ohm cable, but works fine for RX
    • 50 foot length cables always ship immediately
    • Other length cables are now available
      (2 day lead time, but we will try for std time)
    • If you need a more exact length, contact us.
    $2.65$27.95
  • RG6 feedline (White) with F connectors

    0 out of 5
    • RG6 Quad Shield Cable – White Jacket
    • F connectors on each end
    • Factory spec coverage to 3 GHz.
    • UL approved
    • Note: 75 ohm cable, but works fine for RX
    • 50 foot length cables always ship immediately
    • Other length cables are now available
      (2 day lead time, but we will try for std time)
    • If you need a more exact length, contact us.
    $2.65$27.95
  • SMA 50 Ohm 10 dB PAD (attenuator) – GOLD

    0 out of 5
    • Adds 10 dB of attenuation when signals are too strong.
    • Useful with the preamps for a net 10 dB gain.
    • Works inline with the Airspy or Mini
    $14.95
  • SMA 50 Ohm Load – GOLD

    0 out of 5
    • Used for directional couplers or other SMA terminations.
    • Gold plated.
    • 50 Ohm.
    $6.95