These accessories are usually in stock for immediate delivery at no additional shipping charge when purchased with an SDR receiver.
-
1090 MHz ADS-B Filter/Preamp
Uputronics filtered preamps for improved reception on 1090Mhz (ADS-B).
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
137.5 MHz NOAA/APT Filter/Preamp
Uputronics filtered preamps for improved reception on 137.5 Mhz.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB mini cable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 21dB of gain. To stop out of band intermodulation an 137.5Mhz SAW bandpass filter, which has a 7.6MHz bandwidth is also present. The insertion loss of this filter is approximately 1.4dB, which does increase the overall noise figure of the unit to 0.75dB. Connectors are SMA female both sides.
The connectors on both input and output are SMA Female.
Note: This model still uses a USB Mini connector for external power and has no power LED. It has not received the redesign that the other models have received. We have no ETA for that redesign.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
162 MHz Filter/Preamp
Uputronics filtered preamps for improved reception on 159-163 Mhz.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 20dB of gain. To stop out of band intermodulation a 161Mhz SAW bandpass filter, which has a 7.6MHz bandwidth is also present. The insertion loss of this filter is approximately 1.4dB, which does increase the overall noise figure of the unit to 0.75dB
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
3-1200 MHz Directional Coupler
- 3-1200 MHz Directional Coupler
- Inexpensive network analyzer when
used with an SDR and Noise Source. - Used for antenna tuning analysis (reflectometer).
- Gold plated SMA connectors.
- Built-in termination load.
Quick View -
403 MHz Filter/Preamp
Uputronics filtered preamps for improved reception on 403 MHz (Amateur Balloon tracking).
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 21dB of gain. To stop out of band intermodulation a 403Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
434 MHz Filter/Preamp
Uputronics filtered preamps for improved reception on 434 Mhz.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 19dB of gain. To stop out of band intermodulation a 434Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
440 MHz Filter/Preamp
Uputronics filtered preamps for improved reception on 440 Mhz.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 19dB of gain. To stop out of band intermodulation a 440Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
868 MHz / FLARM Filter/Preamp
NOT SUITABLE FOR HELIUM CRYTOMINING (No TX Bypass)
Uputronics filtered preamps for improved reception on 868 MHz (FLARM/LoRa – Receive ONLY.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 16dB of gain. To stop out of band intermodulation a 868 Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
915 MHz Filter/Preamp
NOT SUITABLE FOR HELIUM CRYTOMINING (No TX Bypass)
Uputronics filtered preamps for improved reception on 915 Mhz.
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 16dB of gain. To stop out of band intermodulation a 915 Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB. Connectors are SMA female both sides.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
915 MHz Filter/Preamp with TX BYPASS
This preamp IS suitable for helium cryptomining (it has a TX Bypass)
Uputronics filtered preamps for improved reception on 915Mhz WITH TX BYPASS.
This unit is a filtered preamp designed to go between a radio transceiver and an antenna which gives excellent performance gains for reception and bypasses the preamplification circuit when a transmission is detected.
Power is either via bias tee or a USB-C cable (Not Supplied – See related items for a suitable USB Type A to C Cable). Bias-tee voltage input is 5V.
Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. These particular models are tuned for use with frequencies centred on 915MHz (893MHz-935MHz). The LNA provides around 15dB of gain at 915MHz.
SMA female connectors are fitted for antenna input and radio output, a blue power indicator is provided which switches to red to indicate the unit is bypass mode. The external power connector is a USB-C.
Max TX power +15dBm (30mW)
TX detection threshold -5dBm (+/-2dBm)Data Sheet Here : https://store.uputronics.com/files/FPA-TXB-V6.03.pdf
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
978 MHz UAT Filter/Preamp
Uputronics filtered preamps for improved reception on 978 Mhz (UAT).
This is a cost effective SAW based unit which give excellent performance gains.
All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.
This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.
The LNA used is a MiniCircuits PSA4-5043+ which provides at least 13dB of gain. To stop out of band intermodulation a 978Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.
The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.
Datasheets:
https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdfMechanical diagram:
https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdfQuick View -
ADSB Base Station Antenna C4
- ADSB Base Station Antenna
- Covers ADSB frequencies (1090 MHz)
- Omni-Directional Colinear design (4 element)
- Calculated 6 dB gain (dBd, not dBi)
- White radome
- N connector for durability.
- Length: 22″ (including connector)
- Includes mounting hardware
- Feedline NOT included (add below)
Quick View