Raspberry Pi+ GPS Expansion Board
Power Supply for Broadband Noise Source $8.95
z(DISCONTINUED) LeoNTP (Network Time clock) $425.00
upu-RPiGP

Raspberry Pi+ GPS Expansion Board

Be the first to review

$39.95

This is an GPS expansion board designed specifically for the both the version 1,2 and 3 Raspberry Pi+ Models.

This board is designed for applications that use a GPS connected via the serial ports to the Raspberry Pi such as timing applications or general applications that require GPS information. To facilitate PPS the time pulse output is connected to a GPIO so you can utilize this board to give NTP PPS discipline. PPS does not work without an antenna.

This board is equipped with the latest Ublox MAX-M8Q positioning module and high quality filtering capacitors and inductors throughout. The MAX-M8Q features a RTC Crystal, very low power usage and high performance. Although not a true timing module it is more than adequate for a Pi based NTP Server. Its worth noting the module can, with a serial command, be placed in “Stationary” dynamic mode which is the default mode for the much more expensive timing modules.

The board features an SMA connector for an active patch antenna (see related products) power and PPS LED's. On the top is a super capacitor which can be used to retain any custom settings in the event of power loss (If the module is commanded to do so ). The MAX-M8Q is connected via serial to the Pi and the PPS is connected to GPIO18 (pin 12).

A 2×20 way header is supplied and 2 suitable standoffs providing a very robust solution. The board follows Raspberry Pi's HAT physical layout with camera and display port notches. It is possible to stack additional HAT's on top of this board with the stacking header.

To use this board to make a Stratum 1 NTP Server please follow these instructions here : http://ava.upuaut.net/?p=726

Datasheet available here

For the communication protocol see the u-blox 8 / u-blox M8Receiver DescriptionIncluding Protocol Specification.

(The command to save settings is CFG-CFG)

SKU: UPU-RPiGPS Category: Tags: , , ,
  • Reviews (0)
  • Warranty Info

Reviews

There are no reviews yet.

Be the first to review “Raspberry Pi+ GPS Expansion Board”

Airspy Warranty

Airspy warranty is limited to 1 year from the date of delivery for purchased units that fail under normal operating conditions. Airspy units will be repaired at a price of $50.00 plus $10.00 shipping/handling. Normal operating conditions do not include excessive mechanical stresses due to mishandling, dropping, or bending; mechanical or electrical modifications; Electro-Static Discharge (ESD); excessive RF signals; excessive thermal stresses due to improper ventilation or cooling, submersion in any fluid; and any unauthorized repairs.
All warranty claims will be determined by Airspy or their representatives.

Accessory Warranty (except Filter/preamp)

Accessory warranty (except Filter/Preamp) is limited to 90 days from the date of delivery for accessories that fail under normal operating conditions. The warranty is limited to electrical failiure. Physical damage is specifically excluded unless such damage arises from normal use. Antennas are generally considered ‘disposable items’, although very limited warranties may be honored. All warranty cases will be determined by Airspy.US for these items. Contact us for any warranty claims.

Related Products

  • z(DISCONTINUED) Geaux Robot RPi B+ Dog Bone Case

    0 out of 5
    NOTE: This is a SPECIAL ORDER ITEM at this time.

    Geaux Robot Dog Bone Case for Raspberry Pi B+

    Suitable for Raspberry Pi B+ with our GPS Expansion board.

    For instructions for assembling with the GPS Expansion board click here

    Raspberry Pi and Expansion board NOT supplied.

    If you want to stack these see related items for suitable 25mm stand off kit.

    $19.95
    Read more
    Quick View

  • uBLOX MAX-M8Q GPS Breakout for Active Antennas

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q-10 module and SMA female connector suitable for connecting to a suitable active patch antenna (See related products).

     

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

     

    The board is constructed on 1.6mm PCB and features a PPS LED and Supercap for retaining settings through power cycles. Improved power filtering over previous versions.

     

    On the header are TX, RX, TP (PPS Output), 3V Supply (2.7V to 3.6V), I2C SDA/SCL and GND.

     

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

     

    Supporting temperatures down to -40’C and featuring a TCXO for better power saving and quicker startup the MAX M8Q is an ideal module.

     

    As per the data sheets the MAX M8Q can use upto 22mA under aquisition (5mA in power save mode once tracking).

     

    The breakout has the following dimensions : 22mmx22mmx1.6mm approximately.

     

    The default baud rate is 9600bps.

    $33.95
    Add to cart
    Quick View

  • BNC to MCX GPSDO Pigtail – 12″

    0 out of 5
    • Adapts the clock input to accept a BNC Female connector.
    • RG-316 cable (High Quality / Small Size)
    • Used to connect the GPSDO to Airspy.
    $9.95
    Add to cart
    Quick View

  • SMA 50 Ohm Load – GOLD

    0 out of 5
    • Used for directional couplers or other SMA terminations.
    • Gold plated.
    • 50 Ohm.
    $6.95
    Add to cart
    Quick View

  • z(DISCONTINUED) Geaux Robot RPi B+ Dog Bone Case Stack Kit

    0 out of 5
    NOTE: This is a SPECIAL ORDER ITEM at this time.
    You MUST have a Geaux Robot Dog Bone case first.
    Each kit can add one stack of RPi B+ and you can build many stacks
    A step-by-step guide is included
    $13.95
    Read more
    Quick View

  • z(DISCONTINUED) LeoNTP (Network Time clock)

    5.00 out of 5
    • True Stratum 1 NTP Compatible
      Master Clock / Time Server.
    • Can serve tens of thousands of clients.
    • Very cost effective
    • Supports NTP/SNTP
    • Front OLED Display for time display and configuration
    $425.00
    Read more
    Quick View

  • Raspberry Pi GPS/RTC Expansion Board

    0 out of 5

    NEW FOR 2020 Now with RAW Output & Hardware RTC

     

    The Uputronics Raspberry Pi GPS/RTC Expansion Board provides a modern multi GNSS GPS receiver and hardware RTC with quick no soldering required connection to all Raspberry Pi boards with the 2×20 header (the original Pi Model A/B are not supported). Featuring PPS (Pulse per second) output to permit the use of the board for PPS disciplined NTP servers, RAW output available from the UBlox™ GPS module and twin super caps for GPS hot start/setting retention & maintaining RTC.

     

    This board retains backwards compatibility with previous generation Uputronics Pi GPS boards. With its features and ease of installation we believe this is the ultimate GPS /  RTC HAT for the Raspberry Pi.

     

    GPS Specifications:

    • 72-channel u-blox™ M8 engine
    • Up to 3 concurrent GNSS (BeiDou,Galileo,GLONASS,GPS/QZSS)
    • Default GNSS: GPS/GLONASS.
    • -167dBm Navigation Sensitivity
    • 10Hz navigation rate in multiGNSS mode, 18Hz in GPS only
    • RAW Output available via UBX-RXM-RAWX Message
    • 3V supplied to antenna port to power active antenna
    • Antenna requirements: Active 3V Ceramic Patch
    • No EEPROM settings must be sent at power up or saved to battery backed RAM.
    • Default baud rate: 9600bps
    • I2C Bus (Address 0x42)
    • Robust SMA antenna connection.

     

    For full documentation please consult the u-blox 8/u-blox M8 receiver description including protocol specification document (UBX-13003221) linked here: https://store.uputronics.com/files/UBX-13003221.pdf

     

    RTC Specifications:

    • Micro Crystal RV-3028-C7 Real Time Clock Module
    • Factory calibrated ±1 ppm @ 25°C
    • I2C Bus (Address 0x52)
    • Built in kernel compatibility
    • Provides year, month, date, weekday, hours, minutes and seconds

     

    In The Box

    1 x Raspberry Pi GPS/RTC Expansion Board
    4 x 11mm standoffs w/8 M2.5 Screws
    1 x Header with 4.93mm tails

     
    Full Data Sheet Here : https://store.uputronics.com/files/Uputronics%20Raspberry%20Pi%20GPS%20RTC%20Board%20Datasheet.pdf

    $49.95
    Add to cart
    Quick View

  • uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna

    0 out of 5

    This is new version of the popular pico break outboard, now with SCL & SDA. The board is assembled with a uBLOX MAX-M8C module, chip antenna and a decoupling capacitors.

    This board has VCC, GND and RX & TX, SCL & SDA for I2C.

    IMPORTANT : This module has no onboard voltage regulation so a clean regulated 1.8 – 3.6v power is required. If you want to link this to your microcontroller you must ensure it runs at 1.8 to 3.6v on the serial/I2C or you will risk damaging this module. Arduinos/PC Serial generally run at 5V so you will need a level converter.

    There is no provision for battery backup (V_BCKUP is hard tied to VCC).

    The MAX-8 family delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    MAX comes in an ultra-compact, easy-to-mount 9.7mm x 10.1mm LCC package, and supports temperatures down to -40'C.

    Supports temperatures down to -40'C
    UART interface.
    RTC crystal for faster warm and hot starts
    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.
    Supply Voltage 1.8 to 3.6V

    This module is designed to be as light as possible, weight is very light at 1.5g

    $26.95
    Add to cart
    Quick View

  • Leo Bodnar Icom IC-9700 Reference Injection Board

    0 out of 5
    • Adds frequency reference/stability to the Icom IC-9700
    • This module allows locking the ICOM IC-9700 radio transceiver internal frequency reference, to an external 49.152MHz signal. If the internal reference is locked to a GPS signal, achievable ICOM stability can be better than 1Hz on all bands.
    • Installing this module inside the ICOM IC-9700 does not require any soldering or modification to internal circuitry. This modification is completely reversible and should not affect your warranty.
    • This module is designed to be used and has been tested with the Leo Bodnar GPS reference clocks signal sources.
    $49.95
    Add to cart
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF and UHF radio modules (Special Order item)

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    The MTX2 for 434Mhz transmission is supplied with an RG174 tail to make an antenna. Radio modules will be assembled and tested.
    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix MTX2 434Mhz radio module
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $205.95
    Read more
    Quick View