uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna
z(DISCONTINUED) HABduino Kit + VHF and UHF radio modules (Special Order item) $205.95
uBLOX MAX-M8Q GPS Breakout for Active Antennas $33.95
upu-ublox-m8-pico

uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna

Be the first to review

$26.95

This is new version of the popular pico break outboard, now with SCL & SDA. The board is assembled with a uBLOX MAX-M8C module, chip antenna and a decoupling capacitors.

This board has VCC, GND and RX & TX, SCL & SDA for I2C.

IMPORTANT : This module has no onboard voltage regulation so a clean regulated 1.8 – 3.6v power is required. If you want to link this to your microcontroller you must ensure it runs at 1.8 to 3.6v on the serial/I2C or you will risk damaging this module. Arduinos/PC Serial generally run at 5V so you will need a level converter.

There is no provision for battery backup (V_BCKUP is hard tied to VCC).

The MAX-8 family delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

MAX comes in an ultra-compact, easy-to-mount 9.7mm x 10.1mm LCC package, and supports temperatures down to -40'C.

Supports temperatures down to -40'C
UART interface.
RTC crystal for faster warm and hot starts
Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.
Supply Voltage 1.8 to 3.6V

This module is designed to be as light as possible, weight is very light at 1.5g

SKU: UPU-uBLOX M8 Pico Category: Tags: , , ,
  • Reviews (0)
  • Warranty Info

Reviews

There are no reviews yet.

Be the first to review “uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna”

Airspy Warranty

Airspy warranty is limited to 1 year from the date of delivery for purchased units that fail under normal operating conditions. Airspy units will be repaired at a price of $50.00 plus $10.00 shipping/handling. Normal operating conditions do not include excessive mechanical stresses due to mishandling, dropping, or bending; mechanical or electrical modifications; Electro-Static Discharge (ESD); excessive RF signals; excessive thermal stresses due to improper ventilation or cooling, submersion in any fluid; and any unauthorized repairs.
All warranty claims will be determined by Airspy or their representatives.

Accessory Warranty (except Filter/preamp)

Accessory warranty (except Filter/Preamp) is limited to 90 days from the date of delivery for accessories that fail under normal operating conditions. The warranty is limited to electrical failiure. Physical damage is specifically excluded unless such damage arises from normal use. Antennas are generally considered ‘disposable items’, although very limited warranties may be honored. All warranty cases will be determined by Airspy.US for these items. Contact us for any warranty claims.

Related Products

  • USB MINI Cable for Filter/Preamps (OLDER style)

    0 out of 5
    • NOTE: This cable is for the OLDER STYLE preamps. Most now use the USB-C cable.
      https://v3.airspy.us/product/usb-c-cable-for-filterpreamps/
    • NOTE: Please contact us to make sure which one you need.
    • USB cable for the Filter/Preamps and Preamps that have a USB MINI connector.
    • For use when Bias-T is not available (when Airspy is not used)
    • NOTE: Color may vary
    • NOTE: NOT compatible with Airspy (use OEM cable)
    $2.45
    Add to cart
    Quick View

  • 434 MHz Filter/Preamp

    0 out of 5

    Uputronics filtered preamps for improved reception on 434 Mhz.

    This is a cost effective SAW based unit which give excellent performance gains.

    All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.

    This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.

    The LNA used is a MiniCircuits PSA4-5043+ which provides at least 19dB of gain. To stop out of band intermodulation a 434Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.

    The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.

    Datasheets:
    https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdf



    Mechanical diagram:
    https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdf

    $52.95
    Add to cart
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF and UHF radio modules (Special Order item)

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    The MTX2 for 434Mhz transmission is supplied with an RG174 tail to make an antenna. Radio modules will be assembled and tested.
    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix MTX2 434Mhz radio module
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $205.95
    Read more
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF ONLY radio module

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $169.95
    Read more
    Quick View

  • z(DISCONTINUED) uBLOX MAX-M8Q 3.3V SAW/LNA GPS Breakout With Sarantel Antenna

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q module, front end LNA and Filter.

    The board incorporates an Infineon front end SAW filter and LNA for enhanced performance and faster lock times.

    We have two versions available. This one is suitable for 3.3V microcontrollers and logic levels.

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

    The module is supplied with a 2.54mm 8 way header and a super cap for hot start/setting retention.

    The board is constructed on 1.6mm PCB and utilities the Sarantel/Maruwa SL-1252 Quadrafilar Antenna offering great omnidirectional performance and rejection of out of band signals.

    On the header are TX, RX, EN(Enable – turns on the level convertor on 5V boards), TP (PPS Output), 3/5V Supply I2C SCL/SDA and GND.

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    Supporting temperatures down to -40’C and featuring a TCXO for better power saving and quicker startup.

    The breakout has the following dimensions :

    3V Version 48.5mmx21mm (board edge to top of antenna) x1.6mm (13.2mm antenna diameter) approximately – Weight 10g

    As per the data sheets the MAX M8Q can use up to 22mA under acquisition (5mA in power save mode once tracking).

    The default baud rate is 9600bps.

    For getting started with this module see this wiki article : http://ava.upuaut.net/?p=738

    Datasheet : https://dl.dropboxusercontent.com/u/63720513/HAB%20Supplies%20Datasheets/HAB-BO-M8Q.pdf

    $45.95
    Read more
    Quick View

  • 440 MHz Filter/Preamp

    0 out of 5

    Uputronics filtered preamps for improved reception on 440 Mhz.

    This is a cost effective SAW based unit which give excellent performance gains.

    All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.

    This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.

    The LNA used is a MiniCircuits PSA4-5043+ which provides at least 19dB of gain. To stop out of band intermodulation a 440Mhz SAW bandpass filter, which has a 15MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB.

    The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.

    Datasheets:
    https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdf



    Mechanical diagram:
    https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdf

    $52.95
    Add to cart
    Quick View

  • 1090 MHz ADS-B Filter/Preamp

    4.00 out of 5

    Uputronics filtered preamps for improved reception on 1090Mhz (ADS-B).

    This is a cost effective SAW based unit which give excellent performance gains.

    All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB minicable (Purchased separately). Bias tee/USB voltage is 5V max.

    This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.

    The connectors on both input and output are SMA Female. The external power connector is a USB-C and this revision has a power LED.

    Datasheets:
    https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdf



    Mechanical diagram:
    https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdf

    $52.95
    Add to cart
    Quick View

  • 915 MHz Filter/Preamp with TX BYPASS

    5.00 out of 5

    This preamp IS suitable for helium cryptomining (it has a TX Bypass)

     

    Uputronics filtered preamps for improved reception on 915Mhz WITH TX BYPASS.

     

    This unit is a filtered preamp designed to go between a radio transceiver and an antenna which gives excellent performance gains for reception and bypasses the preamplification circuit when a transmission is detected.

     

    Power is either via bias tee or a USB-C cable (Not Supplied – See related items for a suitable USB Type A to C Cable). Bias-tee voltage input is 5V.

     

    Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. These particular models are tuned for use with frequencies centred on 915MHz (893MHz-935MHz). The LNA provides around 15dB of gain at 915MHz.

     

    SMA female connectors are fitted for antenna input and radio output, a blue power indicator is provided which switches to red to indicate the unit is bypass mode. The external power connector is a USB-C.

     

    Max TX power +15dBm (30mW)
    TX detection threshold -5dBm (+/-2dBm)

     

    Data Sheet Here : https://store.uputronics.com/files/FPA-TXB-V6.03.pdf

    Datasheets:
    https://store.uputronics.com/files/HAB-FPA_Datasheet_Latest.pdf



    Mechanical diagram:
    https://store.uputronics.com/files/LNAMechcanicalDiagramV2.pdf

    $99.95
    Add to cart
    Quick View

  • z(DISCONTINUED) 220 MHz Filter/Preamp

    0 out of 5

    Uputronics filtered preamps for improved reception on 220Mhz.

    This is a cost effective SAW based unit which give excellent performance gains.

    All Uputronics preamps are compatible with most USB SDR Dongles such as the Airspy. You can power them from either bias tee (This item is 100% compatible with the Airspy bias-tee) or a simple USB mini cable (Purchased separately). Bias tee/USB voltage is 5V max.

    This unit is a small filter and preamp designed to go between a software defined radio receiver and an antenna. Using a SAW bandpass filter and a low noise amplifier (LNA), it stops out of band intermodulation while providing additional gain for increased sensitivity. The LNA is before the SAW filter. To block strong commercial FM signals a high pass filter is installed before the LNA.

    The LNA used is a MiniCircuits PSA4-5043+ which provides at least 20dB of gain. To stop out of band intermodulation a 220Mhz SAW bandpass filter, which has a 7MHz bandwidth is also present. The insertion loss of this filter is approximately 2.3dB, which does increase the overall noise figure of the unit to 0.75dB. Connectors are SMA female both sides.

    $52.95
    Read more
    Quick View

  • z(DISCONTINUED) 1090 MHz ADS-B Premium Filter/Preamp

    0 out of 5
    $99.95
    Read more
    Quick View