Raspberry Pi GPS/RTC Expansion Board
uBLOX MAX-M8Q 5V GPS Breakout for Active Antennas $34.95
z(DISCONTINUED) Geaux Robot RPi B+ Dog Bone Case $19.95
UPU-Rpi-GPS-RTC-b

Raspberry Pi GPS/RTC Expansion Board

Be the first to review

$49.95

NEW FOR 2020 Now with RAW Output & Hardware RTC

 

The Uputronics Raspberry Pi GPS/RTC Expansion Board provides a modern multi GNSS GPS receiver and hardware RTC with quick no soldering required connection to all Raspberry Pi boards with the 2×20 header (the original Pi Model A/B are not supported). Featuring PPS (Pulse per second) output to permit the use of the board for PPS disciplined NTP servers, RAW output available from the UBlox™ GPS module and twin super caps for GPS hot start/setting retention & maintaining RTC.

 

This board retains backwards compatibility with previous generation Uputronics Pi GPS boards. With its features and ease of installation we believe this is the ultimate GPS /  RTC HAT for the Raspberry Pi.

 

GPS Specifications:

• 72-channel u-blox™ M8 engine
• Up to 3 concurrent GNSS (BeiDou,Galileo,GLONASS,GPS/QZSS)
• Default GNSS: GPS/GLONASS.
• -167dBm Navigation Sensitivity
• 10Hz navigation rate in multiGNSS mode, 18Hz in GPS only
• RAW Output available via UBX-RXM-RAWX Message
• 3V supplied to antenna port to power active antenna
• Antenna requirements: Active 3V Ceramic Patch
• No EEPROM settings must be sent at power up or saved to battery backed RAM.
• Default baud rate: 9600bps
• I2C Bus (Address 0x42)
• Robust SMA antenna connection.

 

For full documentation please consult the u-blox 8/u-blox M8 receiver description including protocol specification document (UBX-13003221) linked here: https://store.uputronics.com/files/UBX-13003221.pdf

 

RTC Specifications:

• Micro Crystal RV-3028-C7 Real Time Clock Module
• Factory calibrated ±1 ppm @ 25°C
• I2C Bus (Address 0x52)
• Built in kernel compatibility
• Provides year, month, date, weekday, hours, minutes and seconds

 

In The Box

1 x Raspberry Pi GPS/RTC Expansion Board
4 x 11mm standoffs w/8 M2.5 Screws
1 x Header with 4.93mm tails

 
Full Data Sheet Here : https://store.uputronics.com/files/Uputronics%20Raspberry%20Pi%20GPS%20RTC%20Board%20Datasheet.pdf

SKU: UPU-Rpi-GPS-RTC Categories: , Tags: , , , ,
  • Reviews (0)
  • Warranty Info

Reviews

There are no reviews yet.

Be the first to review “Raspberry Pi GPS/RTC Expansion Board”

Airspy Warranty

Airspy warranty is limited to 1 year from the date of delivery for purchased units that fail under normal operating conditions. Airspy units will be repaired at a price of $50.00 plus $10.00 shipping/handling. Normal operating conditions do not include excessive mechanical stresses due to mishandling, dropping, or bending; mechanical or electrical modifications; Electro-Static Discharge (ESD); excessive RF signals; excessive thermal stresses due to improper ventilation or cooling, submersion in any fluid; and any unauthorized repairs.
All warranty claims will be determined by Airspy or their representatives.

Accessory Warranty (except Filter/preamp)

Accessory warranty (except Filter/Preamp) is limited to 90 days from the date of delivery for accessories that fail under normal operating conditions. The warranty is limited to electrical failiure. Physical damage is specifically excluded unless such damage arises from normal use. Antennas are generally considered ‘disposable items’, although very limited warranties may be honored. All warranty cases will be determined by Airspy.US for these items. Contact us for any warranty claims.

Related Products

  • uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna

    0 out of 5

    This is new version of the popular pico break outboard, now with SCL & SDA. The board is assembled with a uBLOX MAX-M8C module, chip antenna and a decoupling capacitors.

    This board has VCC, GND and RX & TX, SCL & SDA for I2C.

    IMPORTANT : This module has no onboard voltage regulation so a clean regulated 1.8 – 3.6v power is required. If you want to link this to your microcontroller you must ensure it runs at 1.8 to 3.6v on the serial/I2C or you will risk damaging this module. Arduinos/PC Serial generally run at 5V so you will need a level converter.

    There is no provision for battery backup (V_BCKUP is hard tied to VCC).

    The MAX-8 family delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    MAX comes in an ultra-compact, easy-to-mount 9.7mm x 10.1mm LCC package, and supports temperatures down to -40'C.

    Supports temperatures down to -40'C
    UART interface.
    RTC crystal for faster warm and hot starts
    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.
    Supply Voltage 1.8 to 3.6V

    This module is designed to be as light as possible, weight is very light at 1.5g

    $26.95
    Add to cart
    Quick View

  • Leo Bodnar LBE-1420 MINI GPSDO (reference clock unit)

    0 out of 5
    • SINGLE output to control Airspy or Spyverter R2x (or other devices)
    • One of the most compact units on the market
    • Powered via USB
    • Comes with GPS Antenna, and USB cable
    • More info: Manufacturer's website
    • Note: Manufacturer's price is shown in Pounds. Our price is the equivalent in Dollars.
    $160.00
    Add to cart
    Quick View

  • SMA 50 Ohm Load – GOLD

    0 out of 5
    • Used for directional couplers or other SMA terminations.
    • Gold plated.
    • 50 Ohm.
    $6.95
    Add to cart
    Quick View

  • Raspberry Pi+ GPS Expansion Board

    0 out of 5

    This is an GPS expansion board designed specifically for the both the version 1,2 and 3 Raspberry Pi+ Models.

    This board is designed for applications that use a GPS connected via the serial ports to the Raspberry Pi such as timing applications or general applications that require GPS information. To facilitate PPS the time pulse output is connected to a GPIO so you can utilize this board to give NTP PPS discipline. PPS does not work without an antenna.

    This board is equipped with the latest Ublox MAX-M8Q positioning module and high quality filtering capacitors and inductors throughout. The MAX-M8Q features a RTC Crystal, very low power usage and high performance. Although not a true timing module it is more than adequate for a Pi based NTP Server. Its worth noting the module can, with a serial command, be placed in “Stationary” dynamic mode which is the default mode for the much more expensive timing modules.

    The board features an SMA connector for an active patch antenna (see related products) power and PPS LED's. On the top is a super capacitor which can be used to retain any custom settings in the event of power loss (If the module is commanded to do so ). The MAX-M8Q is connected via serial to the Pi and the PPS is connected to GPIO18 (pin 12).

    A 2×20 way header is supplied and 2 suitable standoffs providing a very robust solution. The board follows Raspberry Pi's HAT physical layout with camera and display port notches. It is possible to stack additional HAT's on top of this board with the stacking header.

    To use this board to make a Stratum 1 NTP Server please follow these instructions here : http://ava.upuaut.net/?p=726

    Datasheet available here

    For the communication protocol see the u-blox 8 / u-blox M8Receiver DescriptionIncluding Protocol Specification.

    (The command to save settings is CFG-CFG)

    $39.95
    Add to cart
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF and UHF radio modules (Special Order item)

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    The MTX2 for 434Mhz transmission is supplied with an RG174 tail to make an antenna. Radio modules will be assembled and tested.
    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix MTX2 434Mhz radio module
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $205.95
    Read more
    Quick View

  • Power Supply for Broadband Noise Source

    0 out of 5
    • Power Supply for Broadband Noise Source.
    • 12V 1A output
    • 5.5mm/2.1mm coaxial connector.
    $8.95
    Add to cart
    Quick View

  • Broadband Noise Source

    0 out of 5
    • Broadband Noise Source.
    • Used for tuning filters and duplexers.
    • Used as a Network Analyzer RF source.
    • Recommended accuesory: SMA 50 ohm load.
    • 12V 2.1mm coaxial power supply sold separately.
    • Covers 1 MHz to 3.5 GHz
    • Output 60dB @100 MHz to 52dB @1 GHz to 20dB @3.5 GHz
    $29.95
    Add to cart
    Quick View

  • z(DISCONTINUED) Geaux Robot RPi B+ Dog Bone Case

    0 out of 5
    NOTE: This is a SPECIAL ORDER ITEM at this time.

    Geaux Robot Dog Bone Case for Raspberry Pi B+

    Suitable for Raspberry Pi B+ with our GPS Expansion board.

    For instructions for assembling with the GPS Expansion board click here

    Raspberry Pi and Expansion board NOT supplied.

    If you want to stack these see related items for suitable 25mm stand off kit.

    $19.95
    Read more
    Quick View

  • z(DISCONTINUED) uBLOX MAX-M8Q 3.3V SAW/LNA GPS Breakout With Sarantel Antenna

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q module, front end LNA and Filter.

    The board incorporates an Infineon front end SAW filter and LNA for enhanced performance and faster lock times.

    We have two versions available. This one is suitable for 3.3V microcontrollers and logic levels.

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

    The module is supplied with a 2.54mm 8 way header and a super cap for hot start/setting retention.

    The board is constructed on 1.6mm PCB and utilities the Sarantel/Maruwa SL-1252 Quadrafilar Antenna offering great omnidirectional performance and rejection of out of band signals.

    On the header are TX, RX, EN(Enable – turns on the level convertor on 5V boards), TP (PPS Output), 3/5V Supply I2C SCL/SDA and GND.

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    Supporting temperatures down to -40’C and featuring a TCXO for better power saving and quicker startup.

    The breakout has the following dimensions :

    3V Version 48.5mmx21mm (board edge to top of antenna) x1.6mm (13.2mm antenna diameter) approximately – Weight 10g

    As per the data sheets the MAX M8Q can use up to 22mA under acquisition (5mA in power save mode once tracking).

    The default baud rate is 9600bps.

    For getting started with this module see this wiki article : http://ava.upuaut.net/?p=738

    Datasheet : https://dl.dropboxusercontent.com/u/63720513/HAB%20Supplies%20Datasheets/HAB-BO-M8Q.pdf

    $45.95
    Read more
    Quick View
  • 7 %

    z(DISCONTINUED) LeoNTP (Network Time clock) Rack Mount (Triple)

    0 out of 5
    • True Stratum 1 NTP Compatible
      Master Clock / Time Server.
    • Can serve tens of thousands of clients.
    • Very cost effective
    • Supports NTP/SNTP
    • Front OLED Display for time display and configuration
    • Rack Mount with single LeoNTP
    • Note: This is a SPECIAL ORDER item not usually stocked
    $1,399.00 $1,299.00
    Read more
    Quick View