Broadband Noise Source
3-1200 MHz Directional Coupler $29.95
Leo Bodnar GPSDO (reference clock unit) $245.00 $235.00
X-NS-12

Broadband Noise Source

Be the first to review

$29.95

  • Broadband Noise Source.
  • Used for tuning filters and duplexers.
  • Used as a Network Analyzer RF source.
  • Recommended accuesory: SMA 50 ohm load.
  • 12V 2.1mm coaxial power supply sold separately.
  • Covers 1 MHz to 3.5 GHz
  • Output 60dB @100 MHz to 52dB @1 GHz to 20dB @3.5 GHz
SKU: X-NS-1 Category: Tags: , , , , ,
  • Reviews (0)
  • Warranty Info

Reviews

There are no reviews yet.

Be the first to review “Broadband Noise Source”

Airspy Warranty

Airspy warranty is limited to 1 year from the date of delivery for purchased units that fail under normal operating conditions. Airspy units will be repaired at a price of $50.00 plus $10.00 shipping/handling. Normal operating conditions do not include excessive mechanical stresses due to mishandling, dropping, or bending; mechanical or electrical modifications; Electro-Static Discharge (ESD); excessive RF signals; excessive thermal stresses due to improper ventilation or cooling, submersion in any fluid; and any unauthorized repairs.
All warranty claims will be determined by Airspy or their representatives.

Accessory Warranty (except Filter/preamp)

Accessory warranty (except Filter/Preamp) is limited to 90 days from the date of delivery for accessories that fail under normal operating conditions. The warranty is limited to electrical failiure. Physical damage is specifically excluded unless such damage arises from normal use. Antennas are generally considered ‘disposable items’, although very limited warranties may be honored. All warranty cases will be determined by Airspy.US for these items. Contact us for any warranty claims.

Related Products

  • 7 %

    z(DISCONTINUED) LeoNTP (Network Time clock) Rack Mount (Single)

    0 out of 5
    • True Stratum 1 NTP Compatible
      Master Clock / Time Server.
    • Can serve tens of thousands of clients.
    • Very cost effective
    • Supports NTP/SNTP
    • Front OLED Display for time display and configuration
    • Rack Mount with single LeoNTP
    $449.00 $419.00
    Read more
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF ONLY radio module

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $169.95
    Read more
    Quick View

  • Power Supply for Broadband Noise Source

    0 out of 5
    • Power Supply for Broadband Noise Source.
    • 12V 1A output
    • 5.5mm/2.1mm coaxial connector.
    $8.95
    Add to cart
    Quick View

  • uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna

    0 out of 5

    This is new version of the popular pico break outboard, now with SCL & SDA. The board is assembled with a uBLOX MAX-M8C module, chip antenna and a decoupling capacitors.

    This board has VCC, GND and RX & TX, SCL & SDA for I2C.

    IMPORTANT : This module has no onboard voltage regulation so a clean regulated 1.8 – 3.6v power is required. If you want to link this to your microcontroller you must ensure it runs at 1.8 to 3.6v on the serial/I2C or you will risk damaging this module. Arduinos/PC Serial generally run at 5V so you will need a level converter.

    There is no provision for battery backup (V_BCKUP is hard tied to VCC).

    The MAX-8 family delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    MAX comes in an ultra-compact, easy-to-mount 9.7mm x 10.1mm LCC package, and supports temperatures down to -40'C.

    Supports temperatures down to -40'C
    UART interface.
    RTC crystal for faster warm and hot starts
    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.
    Supply Voltage 1.8 to 3.6V

    This module is designed to be as light as possible, weight is very light at 1.5g

    $26.95
    Add to cart
    Quick View

  • 3-1200 MHz Directional Coupler

    0 out of 5
    • 3-1200 MHz Directional Coupler
    • Inexpensive network analyzer when
      used with an SDR and Noise Source.
    • Used for antenna tuning analysis (reflectometer).
    • Gold plated SMA connectors.
    • Built-in termination load.
    $29.95
    Add to cart
    Quick View

  • LeoNTP 1200 Rack Mount Kit

    0 out of 5

    LeoNTP 1200 1U rackmount for mounting one,two or three units (Rack mount kit comes with shelf, screws and 2 blanks. Each kit can take one, two or three LeoNTP 1200 units)

    $150.00
    Add to cart
    Quick View

  • z(DISCONTINUED) uBLOX MAX-M8Q 3.3V SAW/LNA GPS Breakout With Sarantel Antenna

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q module, front end LNA and Filter.

    The board incorporates an Infineon front end SAW filter and LNA for enhanced performance and faster lock times.

    We have two versions available. This one is suitable for 3.3V microcontrollers and logic levels.

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

    The module is supplied with a 2.54mm 8 way header and a super cap for hot start/setting retention.

    The board is constructed on 1.6mm PCB and utilities the Sarantel/Maruwa SL-1252 Quadrafilar Antenna offering great omnidirectional performance and rejection of out of band signals.

    On the header are TX, RX, EN(Enable – turns on the level convertor on 5V boards), TP (PPS Output), 3/5V Supply I2C SCL/SDA and GND.

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    Supporting temperatures down to -40’C and featuring a TCXO for better power saving and quicker startup.

    The breakout has the following dimensions :

    3V Version 48.5mmx21mm (board edge to top of antenna) x1.6mm (13.2mm antenna diameter) approximately – Weight 10g

    As per the data sheets the MAX M8Q can use up to 22mA under acquisition (5mA in power save mode once tracking).

    The default baud rate is 9600bps.

    For getting started with this module see this wiki article : http://ava.upuaut.net/?p=738

    Datasheet : https://dl.dropboxusercontent.com/u/63720513/HAB%20Supplies%20Datasheets/HAB-BO-M8Q.pdf

    $45.95
    Read more
    Quick View

  • Raspberry Pi+ GPS Expansion Board

    0 out of 5

    This is an GPS expansion board designed specifically for the both the version 1,2 and 3 Raspberry Pi+ Models.

    This board is designed for applications that use a GPS connected via the serial ports to the Raspberry Pi such as timing applications or general applications that require GPS information. To facilitate PPS the time pulse output is connected to a GPIO so you can utilize this board to give NTP PPS discipline. PPS does not work without an antenna.

    This board is equipped with the latest Ublox MAX-M8Q positioning module and high quality filtering capacitors and inductors throughout. The MAX-M8Q features a RTC Crystal, very low power usage and high performance. Although not a true timing module it is more than adequate for a Pi based NTP Server. Its worth noting the module can, with a serial command, be placed in “Stationary” dynamic mode which is the default mode for the much more expensive timing modules.

    The board features an SMA connector for an active patch antenna (see related products) power and PPS LED's. On the top is a super capacitor which can be used to retain any custom settings in the event of power loss (If the module is commanded to do so ). The MAX-M8Q is connected via serial to the Pi and the PPS is connected to GPIO18 (pin 12).

    A 2×20 way header is supplied and 2 suitable standoffs providing a very robust solution. The board follows Raspberry Pi's HAT physical layout with camera and display port notches. It is possible to stack additional HAT's on top of this board with the stacking header.

    To use this board to make a Stratum 1 NTP Server please follow these instructions here : http://ava.upuaut.net/?p=726

    Datasheet available here

    For the communication protocol see the u-blox 8 / u-blox M8Receiver DescriptionIncluding Protocol Specification.

    (The command to save settings is CFG-CFG)

    $39.95
    Add to cart
    Quick View

  • z(DISCONTINUED) HABduino Kit + VHF and UHF radio modules (Special Order item)

    0 out of 5

    This board is a GPS receiver and radio transmitter shield designed for tracking high altitude balloon flights utilizing an Arduino Uno/Duemilanove.


    The Habduino Kit Comprises of :


    Habduino Sheild.
    GPS Antenna with 0.5m cable.
    Battery holder + clip


    The MTX2 for 434Mhz transmission is supplied with an RG174 tail to make an antenna. Radio modules will be assembled and tested.
    To track the location of flight you also need a radio receiver, aerial and PC on the ground. Suitable radios include SDR dongles/Airspy – see http://ukhas.org.uk/guides:sdr_tracker for examples of suitable models and full instructions.


    INCLUDES:
    Radiometrix MTX2 434Mhz radio module
    Radiometrix HX1 144.390Mhz (APRS) radio module


    More info: https://store.uputronics.com/index.php?route=product/product&path=62&product_id=57

    $205.95
    Read more
    Quick View

  • LeoNTP 1200 (Network Time clock)

    0 out of 5

    LeoNTP Time Server 1200 is a Stratum 1 Master Clock / Time server with GPS synchronised clock source designed from the ground up with the sole purpose of providing a cost effective but highly accurate and extremely high performing networked time server. Extremely easy to setup and configurable with flexible power options USB/PoE (802.3af) it can provide accurate synchronised time for your LAN, WAN, CCTV, PLC, Telephone systems or anywhere accurate standalone time is required.

    Optional 1U rackmount for mounting one,two or three units (Rack mount kit comes with shelf, screws and 2 blanks. Each kit can take one, two or three LeoNTP 1200 units)

    Optional DIN Rail Mounting Kit

    Unit can sustain 100Mbps (> 100,000 NTP Packets a second)

    Traditional Master Clocks either have high performance or low cost. With LeoNTP Time Server 1200 you can have both in the same package.

    Key Features

    • True Stratum 1 NTP Compatible Master Clock / Time Server.
    • Can serve tens of thousands of clients.
    • Very cost effective
    • Supports NTP/SNTP
    • Front TFT Display for time display and configuration




    Network:
    10/100Mb RJ45 Autosensing
    IPV4 DHCP/Static IP
    IPV6 SLAAC/Static (DHCPv6 not supported)

    Time:
    NTP V2, V3, V4, SNTP V3, V4

    NTP Requests/sec:
    >100K (Wire speed) per unit.
    > 1million concurrent clients typical

    GPS:
    72 Channel
    -167dBm Sensitivity
    Power for active antenna supplied via bias tee.

    Power:
    USB/ 48V PoE 802.3af

    Timing Performance:
    GPS Accuracy:
    30ns RMS, 60ns 99%
    Cold Start acquisition < 30s

    NTP Accuracy:
    < 1µS Hold over on loss of GPS signal Typically 1-4ms in 24 hours Reverts to Stratum 16 after 24 hours with no GPS

    Mechanical Dimension:
    140mm x 170mm x 45mm

    BNC Output:
    PPS/1Mhz/10Mhz Accuracy 30ns RMS, 60ns 99%

    Warranty:
    1 year RTB
    Lifetime Firmware updates and support.

    In The Box :
    1 x LeoNTP Time Server 1200 Device
    1 x GPS Puck Antenna with 3 meter cable
    1 x USB Cable
    1 x 2 meter RJ45 Patch Cable

    See associated items for external timing antenna and BNC to MCX cables.

    Documents:
    LeoNTP 1200 Time Server Manual


    Latest Firmware


    Frequently Asked Questions:

    Q/ Is this unit based on Linux and NTP ?
    A/ No the hardware and code running it are completely propriety and don’t use any source code from Linux or NTP. This is done to ensure maximum performance with no overheads and security issues.


    Q/ Can I configure it via HTTP/Telnet ?
    A/ No. Running a web server on this device although entirely possible would reduce the performance of the unit. Therefore we took the decision to just do configuration via the front panel.


    Q/ The performance figures look too good to be true at the price
    A/ The performance figures are the result of a focused determination to get the best performance out of the hardware. By not using off the shelf hardware and software we have no overheads or compromises. Try it yourself using Miroslav Lichvar's ntpperf tool.


    It only starts to drop when the 100Mb interface is maxed out:



    nevis@test:~/ntpperf$ sudo ./ntpperf -i enp5s0 -m 70:B3:D5:E3:D0:04 -d 172.16.1.72 -s 172.16.1.0/16 -B
    | responses | TX timestamp offset (ns)
    rate clients | lost invalid basic xleave | min mean max rms
    1000 100 0.00% 0.00% 100.00% 0.00%
    1500 150 0.00% 0.00% 100.00% 0.00%
    2250 225 0.00% 0.00% 100.00% 0.00%
    3375 337 0.00% 0.00% 100.00% 0.00%
    5062 506 0.00% 0.00% 100.00% 0.00%
    7593 759 0.00% 0.00% 100.00% 0.00%
    11389 1138 0.00% 0.00% 100.00% 0.00%
    17083 1708 0.00% 0.00% 100.00% 0.00%
    25624 2562 0.00% 0.00% 100.00% 0.00%
    38436 3843 0.00% 0.00% 100.00% 0.00%
    57654 5765 0.00% 0.00% 100.00% 0.00%
    86481 8648 0.00% 0.00% 100.00% 0.00%
    129721 12972 15.49% 0.00% 84.51% 0.00% <- 100Mb Interface Saturated 194581 16384 43.65% 0.00% 56.35% 0.00% 291871 16384 62.43% 0.00% 37.57% 0.00%

    Q/ Can the unit be firmware updated?
    A/ Yes via USB into a Windows PC or Mac. Updates take about 5 seconds to apply.


    Q/ Is the BNC output compatible with the Airspy
    A/ Yes. Set the BNC output to 10Mhz. Connect the unit to your Airspy via the optional BNC to MCX cable and power the Airspy on.


    Q/ Can the unit display my local time ?
    A/ Yes. Press the button on the clock screen and use the knob to select your time zone.


    Q/ Whats the maximum length of coax to the antenna ?
    A/ This depends on the antenna and coax. We've tested our timing antenna (comes with 10 meters of coax) with a 20 meter extension and it works fine. The unit is POE so it may be easier to run a network cable closer to the antenna and install the unit there.


    Q/ Does the unit support IPv6
    A/ Not currently its in the pipeline and will be available to all units on release via firmware update.


    Q/ What happens on loss of GPS Signal
    A/ The unit enters failover mode which uses internal compensation to maintain the accuracy of the timing to 1-4ms typically over 24 hours. After 24 hours with no GPS signal the unit reverts to being a Stratum 16 time source.


    Q/ Leap Second Support
    A/ The unit has leap second support and a count down timer to the next leap second insertion.

    $650.00
    Add to cart
    Quick View