Products

  • SMA to SMA Barrel (Male) – GOLD

    0 out of 5
    • Connects to another SMA Female device, like the 1090 MHz ADS-B Filter/Preamp
    • Gold plating matches the Airspy RF and Preamp connectors.
    $6.95
    Add to cart
    Quick View

  • SMA to SMA Jumper (Male) – 12″

    0 out of 5
    • Connects to another SMA Female device, such as the 1090 MHz ADS-B Filter/Preamp
    • Gold plating matches the Airspy RF and Preamp connectors.
    • RG-316 cable (High Quality / Small Size)
    • Note: Sample pic – may not be identical
    $9.95
    Add to cart
    Quick View

  • SMA to SMA Jumper (Male) – 6″

    0 out of 5
    • Connects to another SMA Female device, such as the 1090 MHz ADS-B Filter/Preamp
    • Gold plating matches the Airspy RF and Preamp connectors.
    • RG-316 cable (High Quality / Small Size)
    • Note: Sample pic – may not be identical
    $9.95
    Add to cart
    Quick View

  • SMA to SMA Pigtail (extension) – 12″

    0 out of 5
    • Adapts the RF connection for tight spaces or stress relief.
    • Gold plating matches the Airspy RF connector.
    • RG-316 cable (High Quality / Small Size)
    $9.95
    Add to cart
    Quick View

  • Spare USB cable (OEM)

    0 out of 5
    • OEM USB cable – identical to the one shipped with the Airspy.
    • Use as a replacement or spare cable.
    • NOTE: Airspy comes with one of these cables.
    $2.45
    Add to cart
    Quick View
  • 17 %

    Spyverter R2

    0 out of 5

     

    • Adapts Airspy to cover 1 kHz to 60 MHz.
    • New R2 version with 80% current draw reduction.
    • GPSDO reference clock input (on board *).
    • 10 MHz instantaneous spectral view.
    • This is NOT “just another upconverter”.
    • The ideal expansion option for your Airspy.
    • Includes two barrel connectors + jumper.
    • No external power required (when powered by an Airspy)
    • NOTE: NO Micro USB power cable is supplied with this package. See below for USB cables when used with non-Airspy/Bias-T SDRs.
    • * External option available. See https://v3.airspy.us/product/spyverter-r2x/

    See https://airspy.com/spyverter-r2/ for specs.

    $59.00 $49.00
    Add to cart
    Quick View
  • 14 %

    Spyverter R2x (External Reference input)

    0 out of 5
    • NOW available with external frequency reference input
    • GPSDO reference clock input (SMA) INCLUDED
    • Adapts Airspy to cover 1 kHz to 60 MHz.
    • New R2 version with 80% current draw reduction.
    • 10 MHz instantaneous spectral view.
    • This is NOT “just another upconverter”.
    • The ideal expansion option for your Airspy.
    • Includes two barrel connectors + jumper.
    • No external power required (when powered by an Airspy)
    • NOTE: NO Micro USB power cable is supplied with this package. See below for USB cables when used with non-Airspy/Bias-T SDRs.

    See https://airspy.com/spyverter-r2/ for specs.

    $74.00 $64.00
    Add to cart
    Quick View

  • Telescopic antenna

    0 out of 5
    • General purpose telescopic antenna
    • Factory spec coverage 144/430 MHz.
    • Tested to cover 136-960 MHz.
    • May cover outside those bands as well.
    • Swivel base is ideal for the Airspy.
    • SMA connector for use with the Airspy.
    $8.95
    Read more
    Quick View

  • Telescopic Magnetic Mount Antenna

    0 out of 5
    • General purpose telescopic antenna
    • Factory spec coverage 144/430 MHz.
    • Tested to cover 136-960 MHz.
    • May cover outside those bands as well.
    • Swivel base is ideal for the Airspy.
    • SMA connector for use with the Airspy.
    • Length: 5″ (13″ extended)
    $8.95
    Read more
    Quick View

  • uBLOX MAX-M8C Pico GPS Breakout with Chip Antenna

    0 out of 5

    This is new version of the popular pico break outboard, now with SCL & SDA. The board is assembled with a uBLOX MAX-M8C module, chip antenna and a decoupling capacitors.

    This board has VCC, GND and RX & TX, SCL & SDA for I2C.

    IMPORTANT : This module has no onboard voltage regulation so a clean regulated 1.8 – 3.6v power is required. If you want to link this to your microcontroller you must ensure it runs at 1.8 to 3.6v on the serial/I2C or you will risk damaging this module. Arduinos/PC Serial generally run at 5V so you will need a level converter.

    There is no provision for battery backup (V_BCKUP is hard tied to VCC).

    The MAX-8 family delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

    MAX comes in an ultra-compact, easy-to-mount 9.7mm x 10.1mm LCC package, and supports temperatures down to -40'C.

    Supports temperatures down to -40'C
    UART interface.
    RTC crystal for faster warm and hot starts
    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.
    Supply Voltage 1.8 to 3.6V

    This module is designed to be as light as possible, weight is very light at 1.5g

    $26.95
    Add to cart
    Quick View

  • uBLOX MAX-M8Q 5V GPS Breakout for Active Antennas

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q-10 module and SMA female connector suitable for connecting to a suitable active patch antenna (See related products).

     

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

     

    The board is constructed on 1.6mm PCB and features a PPS LED and Supercap for retaining settings through power cycles. Improved power filtering over previous versions.

     

    On the header are TX, RX, TP (PPS Output), 5V Supply (4.5V to 30V), I2C SDA/SCL and GND.

     

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

     

    Supporting temperatures down to -40'C and featuring a TCXO for better power saving and quicker startup the MAX M8Q is an ideal module.

     

    As per the data sheets the MAX M8Q can use upto 22mA under aquisition (5mA in power save mode once tracking).

     

    The breakout has the following dimensions : 22mmx22mmx1.6mm approximately.

     

    The default baud rate is 9600bps.

    $34.95
    Add to cart
    Quick View

  • uBLOX MAX-M8Q GPS Breakout for Active Antennas

    0 out of 5

    This is an assembled breakout board with a uBLOX MAX-M8Q-10 module and SMA female connector suitable for connecting to a suitable active patch antenna (See related products).

     

    Suitable for HAB Usage Max Altitude 50,000 meters / 164041 feet in Flight Mode.

     

    The board is constructed on 1.6mm PCB and features a PPS LED and Supercap for retaining settings through power cycles. Improved power filtering over previous versions.

     

    On the header are TX, RX, TP (PPS Output), 3V Supply (2.7V to 3.6V), I2C SDA/SCL and GND.

     

    The MAX-M8Q delivers all the benefits of the u-blox 8 GPS platform in a more compact form factor than ever before: high-sensitivity, intelligent power management.

     

    Supporting temperatures down to -40’C and featuring a TCXO for better power saving and quicker startup the MAX M8Q is an ideal module.

     

    As per the data sheets the MAX M8Q can use upto 22mA under aquisition (5mA in power save mode once tracking).

     

    The breakout has the following dimensions : 22mmx22mmx1.6mm approximately.

     

    The default baud rate is 9600bps.

    $33.95
    Add to cart
    Quick View